+8615628781468
sellelevator@163.com
The lifting platform shall be placed in a trench position， and take out the lower bearing and oil suction device; Slowly test run and check whether the surface around the axle diameter is seriously damaged; If the damage is serious and tungsten is occupied remove the axle oil box， polish it with oilstone; Under the motor， and with the sleeper on the trench edge inside the rail， use the jack to periodically pull the motor and remove the upper tile; How to solve the damage of the important equipment in the lifting platform? Check the status of the bearing pads and oil absorbers， investigate the cause of the damage，Products replace the bearing pads，JinchengConstruction site lifting cargo elevatorThe decline of social inventory has accelerated and clean the bearing oil box; After assembling all parts and components， install a new oil suction device on the axle oil box and inject clean axle oil; The gear box shall be filled with gear lubricating oil as required; Burn of axle box bearing is the most common one， which is the outer row bearing. If it is serious， the axle box and wheel set will be fixed together， especially for the equipment that has been used for a long time. The reasons for the abnormal noise are as follows: The hydraulic lifting platform often encounters fault overload in the process of use: because of overload， the hydraulic lifting platforms own bearing capacity is overloaded. It is the same as the reason that people will shout when they go to carry things overloaded， so， Never overload!
aby a riverRegularly check and repair whether the circuit system of the hydraulic lifting platform is loose， and check whether the wires and cables are aging and damaged which causes electric leakage of the line. If any，Products repair it in time to avoid electric shock.
The series of standards related to mobile elevators is a series of standards compiled by the Construction Mechanization Research Branch of the Construction Research Institute in accordance with the task of formulating and revising the product standards of the Ministry of Construction in accordance with the Construction Standard No. and [] of the Ministry of Construction. The series of standards refer to ANSI A— Boom Lifting Platform and ANSI-A— Self-propelled aerial operation platform standard， with reference to relevant European industrial standards. This standard passed the review of relevant Chinese departments on January ， . The review opinion is that the series of standards for aerial work platforms are comprehensive in content， strong in compatibility and sufficient in basis， reflecting the progressiveness and scientificity of the standards， and the main performance indicators reach the international advanced level. This standard was issued on /The safety requirements and specifications of the project site shall be observed. It is strictly forbidden to use equipment in violation of rules and regulations. The following safety protection shall be paid attention to during the industrial control operation: before using the safety helmet， check whether the safety helmet shell， helmet lining and helmet belt are complete， safe and effective.
Vteheran or tehranSome office buildings and hospitals may need several or even dozens of passenger lifts. In order to increase the speed， efficiency and area of the electric lift，Products most high-rise buildings will divide the electric lift into an array， each group is responsible for some floors，JinchengConstruction site lifting cargo elevatorThe decline of social inventory has accelerated and make different adjustments and scheduling according to the use mode of different floors at different times.
IuJust like the failure of the traveling part of the lifting platform， the operator must master the common sense of equipment maintenance failure， so that when the failure occurs， it will not appear too flustered. Generally speaking， the common faults of the traveling part of the lifting platform are divided into:; The bearing bush is burnt， the axle box bearing is burnt， the traction motor bearing is burnt， the tyre is loose，Cargo elevator_ Electric elevator_ Electric lifting table_ Lifting equipment_ Lift equipment_ Aluminum alloy elevator - cargo elevator factory and the crack is damaged. Lets share the solution with you.
It is necessary to check the brake of the guide rail elevator frequently. There should be no dirt on the friction surface.
For the introduction of daily maintenance of the elevator the brake of each organization should generally inspect and adjust the interval between the brake shoe and the brake wheel to ensure that it is sensitive and reliable. There should be no dirt on the surface. If there is any dirt， it must be washed off with gasoline or thinner.
oWhether it is used outdoors or indoors， it is inevitable that some small problems will occur after a long time. At this time， what we should do is to maintain and maintain the elevator. How to follow the steps correctly becomes a difficult problem. Let me explain it to you.
JGenerally， check the connection of each part， effectively prolongs the service life and simplifies the maintenance.
kEWhat are the safety tools explosion-proof valves on mobile elevators? They are often seen in large hydraulic equipment， especially heavy equipment. The main effect is to avoid the problems of equipment caused by oil circuit cracking or excessive oil pressure. The installation of small elevator explosion-proof valves depends on the needs of customers， but large equipment basically needs to be installed.
The damaged part of the elevator that needs to be bandaged and replaced in time is a kind of hydraulic elevator， also known as guide rail hydraulic elevator， which is applicable to the transportation of goods higher than buildings， restaurants and hotel floors. Here is Lipson Machinery to introduce the daily maintenance of the elevator.
Loosening: The newly processed and assembled parts of mobile elevators and other aerial work platform equipment have a tendency to geometric shape and fit size. At the initial stage of use， due to the impact of alternating loads such as impact and vibration， or the impact of heating， deformation and other factors， as well as reasons such as excessive wear， it is easy to make the original fastening parts of mobile elevators and other aerial work platform equipment loose.
Online consultationpThe explanation is mainly from the mechanism of the lifting platform. Now there are many different types of lifting platforms. In order to better use the lifting platform， we have started to develop different lifting platforms for different industries. The electric lifting platform has become the main product of the small lifting platform. It is small in size， light in weight， generous in appearance and practical， stable and free in lifting， large in carrying capacity and large in plane area， Stability has become the machinery that many customers compete for. Lifting equipment is used in enterprises of all sizes， so the use of lifting platform is necessary.
NThe lift has strong bearing capacity and is suitable for two people (can carry certain weight tools and materials) to climb at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
The product has solid structure， large bearing capacity， stable lifting， easy installation and maintenance， and is an economic and practical ideal cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the daily maintenance of the elevator: when the personnel enter the elevator to work， they must hang the elevator to prevent the elevator from suddenly falling and causing casualties.
bby a riverThe daily maintenance of the guide rail elevator should ensure that the transmission position where the grease nipple is located needs to be greased twice a month. For the parts that cannot be greased， be sure to dredge the oil circuit or replace the grease nippleNo， otherwise it is forbidden to use the equipment.
kZKeep the access road of external construction elevator smooth and have enough space for parking equipment. When the auxiliary installation of the crane is required， full consideration shall be given to whether the site environment meets the operating conditions of the crane.
How to properly handle the elevator after water ingress to keep the elevator high in front and low in back as far as possible， which is beneficial to discharge the water entering the exhaust pipe and avoid damage to the converter.