Jade SpringFixed lifting hydraulic cargo elevatorHow is it made

Scissor type aerial work platform In Europe and the United States and other regions， the development of aerial work platform technology has been quite mature. It is widely used in various fields such as emergency rescue， aerial work， fire protection， etc. In China， aerial work platforms have not been used for a long time，Electric lifting table mainly in construction，XinleFixed hydraulic lifting cargo elevatorWhat properties should the material have transportation， industrial plants and other industries. With the continuous development of social economy and the continuous growth of enterprise demand， especially in recent years， the state has increased investment in infrastructure construction， which has brought a better prospect for the development of the platform industry.

4The lifting height is stable， which can meet the requirements of stable lifting of large-tonnage goods. The hydraulic lifting stage is equipped with anti-attachment and overload protection hydraulic system to ensure operation. Is a long-term operating elevator factory welcome to consult

qJade SpringCheck whether all travel switches are loose. If yes， tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; Pin shaft Check whether the pin shaft (ear pin shaft and center pin shaft) is dry. If some are dry， nuts， screws，Electric lifting table etc. are loose on site， and if so， immediately reinforce them; Ensure that the hydraulic lifting platform lifts smoothly; Outrigger (for aerial work platform)

It is forbidden to use safety belts to transfer heavy objects; The safety belt shall be hung at a firm and reliable place above， and the height of the safety belt shall be higher than the waist. Professional sales elevator factory safety， environmental protection， economic! The products are exported to foreign countries and deeply trusted

Zkelowna The motor does not rotate: the motor is broken， contact the manufacturer for treatment.

FzIn recent years， there are no more than three factors that lead to the occurrence of domestic elevator accidents in mobile elevator manufacturers. They are human operation errors， which are purely caused by the lack of relevant equipment operators. The second is the simple hoist that has been screened in China and is not allowed to be used. This kind of hoist is potentially dangerous. And because the country has banned the production of this kind of simple hoist， the existing equipment is often aging，Electric lifting table which is more prone to accidents. The third is that the quality of production is not up to standard， leading to severe social security incidents.

In recent years there are no more than three factors that lead to the occurrence of domestic elevator accidents in mobile elevator manufacturers. They are human operation errors，XinleFixed hydraulic lifting cargo elevatorWhat properties should the material have which are purely caused by the lack of relevant equipment operators. The second is the simple hoist that has been screened in China and is not allowed to be used. This kind of hoist is potentially dangerous. And because the country has banned the production of this kind of simple hoist， the existing equipment is often aging， which is more prone to accidents. The third is that the quality of production is not up to standard， leading to severe social security incidents.

Generally， check the connection of each part， hydraulic mechanism， electric mechanism and support mechanism. The hydraulic oil forms a certain pressure from the vane pump and enters the lower end of the hydraulic cylinder through the oil filter flameproof electromagnetic directional valve， throttle valve，Cargo elevator_ Electric elevator_ Electric lifting table_ Lifting equipment_ Lift equipment_ Aluminum alloy elevator - cargo elevator factory hydraulic control check valve and balance valve， so that the piston of the hydraulic cylinder moves upward and lifts the weight. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the flameproof electromagnetic directional valve， and its rated pressure is adjusted through the overflow valve. Observe the reading value of the pressure gauge through the pressure gauge.

WHydraulic boarding axle“ Streamlined” The open loose-leaf joint design increases the welding area by more than times than the ordinary tubular joint， effectively prolongs the service life and simplifies the maintenance.

JProduct surveyThe safety belt needs to be checked every six months. The load is kg and the test time is five minutes. After the test， check whether the safety belt is broken or deformed， and make a record of the test. The unqualified safety belt should be stopped immediately.

mNAfter careful inspection， it was found that it was mainly caused by two reasons: the loss of hydraulic pressure and the leakage of hydraulic valve or seal.

The second is that steel will have obvious thermal expansion and contraction effect at low temperatureThe nature of steel will be taken into account at all times， but after all， the environment is different. Under low temperature conditions， steel will have some unstable performance， such as increased hardness and decreased toughness. At this time， more attention should be paid to the maintenance of equipment to keep the key parts lubricated to avoid dry grinding.

Scissor-type aerial work platform is a professional aerial work equipment with a wide range of uses.

Lets seemThe concept of hydraulic boarding bridge The boarding bridge uses the power system. The large oil cylinder raises the entire equipment inclined plate. When it rises to the large height， the small oil cylinder starts to work and stretches out the loose-leaf tongue. All the equipment plates are effectively welded with high quality checkered steel plates and profiles with long service life.

HThe reason for the elevator overheating is that the mechanical load dragged is not working normally. Although the equipment is complete， the mechanical load dragged by it is not working normally. The load varies from large to small during operation. For example， when the feeding amount of thresher is too large， which can effectively avoid injuring the toes of the operator when the adjusting plate falls， so as to ensure the safety of the equipment.

jJade SpringIn case of overheating of the motor during the daily maintenance of the elevator， park the car immediately， remove the obstacles， and then continue to run. The motor bearing should be smooth and excellent.

zVDrain the hydraulic oil of the hydraulic elevator and discard it. For the outdoor guide rail elevator， tighten the connector and take out the oil filter. After cleaning， clean it with compressed air， and then put it back into the oil tank and connect the pipeline.

The novice should pay attention to which equipment wears fast when operating the mobile lift: due to the processing and installation of the components of the mobile lift and other aerial work platform equipment， the small contact area， and uneven load bearing， the equipment will wear. During the operation of mobile elevator and other aerial work platform equipment， the concave and convex parts on the surface of the parts are embedded and friction with each other. The secondary friction between metal debris and the equipment will accelerate the wear of the surface of the equipment parts. Therefore， mobile elevators and other aerial work platform equipment are prone to wear and tear of parts and components during the running-in period， and the wear speed is fast.