YunnanFixed lifting cargo elevatorHow to improve the pumping efficiency

It is forbidden to stay below the working place at height， and safety nets or other protective devices shall be set below the working place to avoid injury caused by falling objects.

5For this reason

It is forbidden to stay below the working place at height， many mobile elevators will be equipped with various protective equipment to ensure the safety of peoples lives. Now lets see what safety tools are on the mobile elevator?

aYunnanThe lifting table does not lift when the voltage is too low. Check the starter potential when the motor is working with load. Allowable hydraulic range of voltage± % of the motor does not rotate. Check whether the motor and circuit motor are reversed and arbitrarily change the two phases in the three-phase line.

The price of the elevator is too early to open the package. We should not open the package in advance before installing the elevator bearing. This will simply lead to premature pollution of the bearing， which will lead to premature damage of the bearing. In addition， we should ensure that the device environment is clean when installing， and do not bring iron filings，Electric elevator dust，HuozhouFixed guide rail type cargo elevatorFactors that delay corrosion and other things into the bearing， because even some small dust， If it goes on for a long time， it will also affect the running-in between the bearings， resulting in a decline in the life of the elevator.

SWal maranstadHow to use the safety belt correctly when the mobile elevator is working at height: the belt should be fastened when using， and the waist buckle accessories must be tightened and fastened; When using the safety belt for aerial suspension operation， the safety belt hook cannot be directly hooked on the safety belt rope but must be hooked on the hanging ring of the safety belt rope; It is strictly forbidden to hang the safety belt on the unstable or sharp-angled components; It is forbidden to replace all parts on the safety belt; It is forbidden to use the safety belt with obvious deformation or severe impact.

PaIt is easy to cause the deterioration of lubricating oil in the process of wading. Especially in the steering， transmission and other systems， the site should be disassembled and inspected. When the elevator is flooded，Electric elevator everyone should pay attention to it. The above points should not be ignored.

The safety belt needs to be checked every six months. The load is kg and the test time is five minutes. After the test， check whether the safety belt is broken or deformed， and make a record of the test. The unqualified safety belt should be stopped immediately.

Manual hydraulic platform classification: manual hydraulic lifting platform car can be divided into manual hydraulic handling platform car， manual hydraulic stacking platform car， and manual hydraulic shear platform car.

pHow to judge the clean oil quantity of the lift to the hydraulic station? Why cant we wash the lift hydraulic station with water?

BWhen using the helmet， the helmet should be tightened and worn correctly， and the helmet strap should be fastened under the mouth and jaw and tightened.

FHow many?. High-pressure water abrasive derusting. It is a kind of screw elevator that uses the impact of high pressure water jet and abrasive to polish and remove rust. It has the advantages of little damage to the material， but water has certain damage to electronic equipment. It is applicable to the removable type of screw elevator.

pMThe daily maintenance of the cargo elevator should be carried out by a professional team (issued by the AQSIQ).

The daily maintenance of the guide rail elevator should ensure that the transmission position where the grease nipple is located needs to be greased twice a month. For the parts that cannot be greased， be sure to dredge the oil circuit or replace the grease nippleNo， otherwise it is forbidden to use the equipment.

The hydraulic lifting platform has abnormal noise. It is normal for the hydraulic lifting platform to make abnormal noise，Electric elevator especially for the equipment that has been used for a long time. The reasons for the abnormal noise are as follows: The hydraulic lifting platform often encounters fault overload in the process of use: because of overload， the hydraulic lifting platforms own bearing capacity is overloaded. It is the same as the reason that people will shout when they go to carry things overloaded，HuozhouFixed guide rail type cargo elevatorFactors that delay corrosion so， Never overload!

Analysis projectfCheck the hydraulic oil quality and level. When the lifting platform is raised to a high level， the hydraulic oil level should be -mm higher than the bottom of the oil tank. When the color of the hydraulic oil becomes dark， the oil is sticky or there is sand and other foreign matters in the oil， the hydraulic oil should be replaced in time. The hydraulic system of the lifting platform shall be used to check the hydraulic and pipe connections. Replace the damaged pipe immediately; Tighten the pipe joint when the connection part is loose.

RPurpose Hydraulic elevators are widely used in various industrial enterprises and production lines， such as automobile， container， mold manufacturing，Cargo elevator_ Electric elevator_ Electric lifting table_ Lifting equipment_ Lift equipment_ Aluminum alloy elevator - cargo elevator factory wood processing， chemical filling， etc.， to meet the lifting requirements of different working heights， and can be equipped with various table forms (such as ball， roller， turntable， steering， tilting， telescoping)， and with various modes (transfer， linkage， explosion-proof)， with the characteristics of stable and accurate lifting， and large load capacity， Effectively solve all kinds of lifting operation difficulties in industrial enterprises， and make production operation easy and free. Professional sales elevator factory has advanced technology， strict testing， more affordable price and more preferential treatment. Welcome to consult

Therefore， before the operation of the lifting platform， the operators shall provide the operators with operation skills and safety information， including: operation contents and requirements; Safety matters and dangerous points; Division of labor and scope of responsibility. The operator should not only check the condition of the vehicle and the operator， but also check whether the terrain environment， takeoff and landing meet the needs of safety skills or the pre-established operation plan. For those with income and expenditure， or the impact of heating， deformation and other factors， as well as reasons such as excessive wear， it is easy to make the original fastening parts of mobile elevators and other aerial work platform equipment loose.

mQThe development history and current situation of scissor-type aerial work platform With the increasingly widespread use of vehicle-mounted aerial work platform in production， it has gradually been recognized by various industries and began to be applied in other industries with similar working conditions. With the continuous expansion of the scope of application， such as its huge size is difficult to use in a narrow working space， and the high-speed drive function cannot play its role in a narrow space. In addition， if the hydraulic stabilizer configured on the old vehicle-mounted platform fails， the equipment can not continue to be used. These limitations greatly reduce the working efficiency of the equipment. In order to meet the market demand in the middle and late s， a new type of production leveling&mdash& mdash; Self-propelled remote control aerial work platform came out. Since the birth of this new product the field of aerial work platforms has grown rapidly. It is also from this beginning that the global aerial work platforms have begun to develop in the direction of serialization. The structure and production process of this self-propelled remote control aerial work platform are relatively simple. A large number of improved aerial work platform products have entered the American market in large quantities. With the popularity of this product， some new contradictions have emerged. In some special occasions， such as gypsum process， lead process， live working and fire rescue， the scissor type aerial work platform came into being. Due to a large number of electric designs， the scissor-type aerial work platform can move freely in a narrow space， and even can be used on some fragile ground and bearing ground. At present， the demand for scissor-type aerial work platform is increasing， and its proportion in the rental industry has even reached %. Professional sales of goods elevator factory and other products with a complete range， best-selling equipment at home and abroad， long service life! Product wire product industry leader， welcome to call for consultation

The loading and unloading mobile boarding bridge has become a very visible structural form in modern logistics sites. It is the starting point and end point of the enterprise logistics chainUnloading operation platform. The height of the loading and unloading operation platform is fixed， but the height of the carriage to and from the ground does not always form a certain height difference or gap between the transport vehicle and the loading and unloading platform. As a result， the forklift can not enter and exit the transport vehicle to directly load and unload goods. Use the boarding bridge to provide reliable connection. It enables the forklift truck to enter and exit the transport vehicle quickly for loading and unloading.